ACS BoroTreat 10P ( Call to order )

  • £11.84
  • Ex VAT: £9.87

Available Options


  • ACS BoroTreat 10P ( Call to order )

Boron powder for trade professionals

This is a professional use only product please call us on 01935 414012 or email info@acslimited.co.uk to order this product.


ACS Borotreat 10P is a multipurpose Boron powder concentrate for use as a wood preservative. It is a very effective fungicidal and insecticidal control treatment, which will also prevent re-infestation.

ACS Borotreat 10P is suitable for all wood, which is not in direct contact with the ground or exposed externally.

ACS Borotreat 10P is supplied in convenient pack sizes as 100% w/w Disodium octaborate tetrahydrate ( Na2B8O13·4H2O ) as the active ingredient. It is easily diluted with water and provides permanent protection, as the active ingredient does not break down.

This is a professional use only product

SPECIAL PROPERTIES

• Excellent internal preservative for the control of wood rotting fungi and wood destroying insects

• Approved under EU Biocides Products Regulations for use as a wood preservative

• 1 hour re-entry time

• Cost effective, clean and easy to handle

• Odourless and non-flammable

• Permanent protection as the active ingredient does not break down

• Convenient pack sizes

DIRECTIONS FOR USE AND PACK SIZES

Dilute ACS Borotreat 10P 1 in 9 with clean tap water to give a 10% active working solution*.

ACS Borotreat 10P is supplied in convenient pack sizes of 0.1, 0.5 and 2.5kg to make 1, 5 or 25 litres of diluted product respectively. Use an oversized bucket or container with the appropriate volume of clean tap water and add the corresponding amount of powder concentrate. Mix the powder into the water with a suitable paddle during addition and continue until it has completely dissolved. Use warm water if possible to help the powder to dissolve.

The working solution of ACS Borotreat 10P can be applied by brush, spray (microblower) or injection.

USE AS A WOOD PRESERVATIVE

1. Clean all wooden surfaces using a brush or vacuum cleaner.

2. Cover electrical installations, water tanks, stored goods and isolate adjacent areas not requiring treatment.

3. Lift floorboards as required and clean out debris.

4. Treat all accessible areas with the working solution of ACS Borotreat 10P using brush or spray (microblower).

5. Under normal circumstances one coat will be sufficient but ensure that all accessible wood surfaces are thoroughly wetted out. Any surfaces that absorb solution rapidly should be sprayed again at the time.

6. Apply a second coat after one to eight hours where there is a severe fungal attack or woodworm infestation.

COVERAGE

By Brush : 1 litre to 6 – 8 m2 using a 10% solution

By Coarse Spray : 1 litre to 4 – 6 m2 using a 10% solution

By Injection : Apply a 10% solution through 3mm diameter predrilled holes

(* in some cases as a superficial treatment against Anobium punctatum apply a 4% solution at 4m2/litre)

SHELF LIFE AND STORAGE

Indefinite shelf life in unopened, sealed packs or containers.

Store in the original packaging, unopened or sealed in a dry, safe place.

HEALTH AND SAFETY

ACS Borotreat 10P is approved under the EU Biocides Product Regulations for use as directed. Authorisation Number: UK-2014-0872.

Refer to Safety Data Sheet (SDS) for the product.

Contains: 100% Disodium octaborate tetrahydrate Boron Power

Use only as a wood preservative. Keep away from children and always read the label.

Borotreat 10P Technical Data Sheet
Borotreat 10P Safety Data Sheet

Write a review

Note: HTML is not translated!
Captcha

Tags: Wood Preservation, Boron powder